- Induction Heating steel mandrel tip Class: Induction Thermal Treatment
Intro: Heating steel mandrel tip Objective Heat a water-cooled steel mandrel to 700F (371C) to form a high quality Teflon catheter tip.Material Teflon catheter tubing, mandrel assemblyTemperature 600-700F (315-371C)Frequency 376 kHzEquipment • Power of 10kW…
- Induction Heating Catheter Tipping Die Class: Induction Thermal Treatment
Intro: Heating Catheter Tipping Die Objective: To heat an aluminum catheter tipping die to above 2850F within 2 to 5 seconds for the forming of catheter material. Presently, heating is performed in 15 seconds with older induction equipment. The customer woul…
- Induction Heating fan blades for welding Class: Induction Welding
Intro: Heating fan blades for welding Objective To uniformly heat jet engine turbine fan blades to 1800F (982.2C) within five minutes for a welding applicationMaterial Jet engine turbine fan blades with 2”(50.8mm) length tipTemperature 1800F (982.2C)Frequen…
- Induction Soldering Co-axial Wire Class: Induction Soldering
Intro: Soldering Co-axial Wire Objective To solder center-conductor and shielding braid of wireassemblies to 500 (250) F(C).Material • Customer-supplied assemblies• Temperature indicating paint• Flux-cored solder wireTemperature 500 (250) F (C)Frequency 2…
- Induction Soldering wires onto connector Class: Induction Soldering
Intro: Soldering wires onto connector Objective Heat connector assemblies for solderingMaterial Device assemblyTin plated brass terminals Solder pasteTemperature 500F (260C) 5-7 secondsFrequency 360 kHzEquipment Power of 6 kW induction heating system equippe…
- Induction Soldering satellite antennas Class: Induction Soldering
Intro: Soldering satellite antennas Objective Soldering steel onto GPS body for phone antennaMaterial Thin copper foil 0.3mm (0.01 in) thick Ceramic body 12mm (0.47 in.) long x 7mm (0.28 in.) wideTemperature 200 C (392 F)Frequency 371 kHzProcess Time 5 secon…
- Induction Soldering brass Class: HF Induction Brass Solder
Intro: Soldering brass Objective To solder a brass end cap to a series of copper tubesMaterial Preassembled heat exchanger with copper tubes and 2 brass end caps 2.36” (60mm) OD, 0.08” to 0.12” (2 to 3mm) thick at both ends, liquid solderTemperature 302F …
- Induction Soldering circuit boards Class: Induction Soldering
Intro: Soldering circuit boards Objective To heat post, lead or lead-free solder preforms for various circuit board soldering applications.Material Upper and lower circuit boards, small and large lead or lead free preforms.Temperature < 700 F (371C) depen…
- Induction Soldering brass and copper Class: HF Induction Brass Solder
Intro: Soldering brass and copper Objective To heat brass and copper for soldering application on medical equipmentMaterial Brass ring, brass and copper pieces 5.11” (130mm) long, 4.3” (110mm) OD & 0.3” (7mm) at thickest point and solder ringsTemperat…
- Induction Soldering fabric to kovar tip Class: Induction Soldering
Intro: Soldering fabric to kovar tip Material Kovar cone, base 3/8” (9.5mm) dia, cone 3/8” (9.5mm) high, solderTemperature 300 F (149 C)Frequency 242 kHzEquipment • Power of 3.2 kW induction heating system, equipped with a remote workhead containing one 1…
Recommended
Air Cooled clamp coil (half-open coil) for preheating gas pipeline
U shape air cooled induction coil by UM-100C-HF for pipeline preheating
induction brazing diamond segment
induction melting for crystal growth
induction unassemble 2Ton guard ring of turbine
induction preheating D5000mm end ring for welding by 2 UM-DSP80A-HF at the same time
induction preheating D1219mm pipeline for welding by UM-DSB80AB-MF air cooled induction heater and i
induction preheating and heat treatment for 18Ton control valve of 600MW turbine