- Induction Preheating oil drilling shaft Class: Induction Tempering or Preheating
Intro: Preheating oil drilling shaft Objective To preheat a steel pipe to 500F (260C) before welding.Material Steel shaft assembly 5” to 8” OD (127-203.2mm) with a 2” (50.8mm) heat zone.Temperature 500F (260C), if higher temperatures are required, heat ti…
- Induction Sintering copper powder Class: HF Induction Brazing
Intro: Sintering copper powder Objective Sintering copper powder to a stainless steel shaftMaterial Steel shaft & shell assembly, approx 2” (50.8mm) diameter, 2” (50.8mm) tall, copper powderTemperature 1600 F (871 C)Frequency 54 kHzEquipment • Power o…
- Induction Heating motor Class: Other Induction Applications
Intro: Heating motor Objective Heat steel to help bond an injection molded piece and help the reflow.Material Steel motor body, 60 x 60 x 27 (2.4 x 2.4 x 1.1) mm(in)Temperature 260C (500F)Frequency 237 kHzEquipment • Power of 20kW induction heating system, …
- Induction Heat braided cable Class: Other Induction Applications
Intro: Heat braided cable Objective Prior to cutting, heat a short section of a hardened steel cable coated with a polyethylene sheathing.Material Multi-strand braided stainless steel cable 0.5 in. (1.27 cm) OD enclosed within a polyethylene sheathingTempera…
- Induction Hermetically sealing glass Class: HF Induction Brazing
Intro: Hermetically sealing glass Objective Provide a hermetic seal of glass enclosed resistor to a leadMaterial ResistorKovar rings, 0.1 inch (0.254cm) diameterGlass tube slightly larger than 0.1 inch (0.254cm) diameter, 0.5 (1.27) inch lengthMetal leadTemp…
- Induction Tempering Spring Class: Induction Tempering or Preheating
Intro: Tempering Spring Objective Temper a spring by heating it to 300C (570F) in 2 – 4 secondsMaterial Stainless steel AISI 302 springs- different length from 60 to110 mm outer diameters 8 mm.- wire diameter from 0.3 to 0.6 mmTemperature 300C (570F)Freque…
- Induction Heat the end of catalytic converter Class: Other Induction Applications
Intro: Heat the end of catalytic converter Objective Heat the end of lorry catalytic converter exhaust system. The assembly must be held at target temperature for 200 hours, whilst the assembly is vibrated to test the weld strength.Material SteelTemperature …
- Induction Heat the plough discs Class: Other Induction Applications
Intro: Heat the plough discs Objective To heat the circumference of plough discs before hot rolling (sharpening) processMaterial Flat Boron steel discs, OD 460 to 710 mm (18 to 28”) thickness 3.2 to 10 mm (8/64 to 25/64”)Temperature 725C 1335FFrequency 75 …
- Induction Heating steel rivets Class: Induction Jointing
Intro: Heating steel rivets Objective Heating steel rivets prior to head formingMaterial steelTemperature 1292 F (700C)Frequency 83 kHzEquipment • Power of 7 kW induction heating system, equipped with a remote workhead containing one 1.5μF capacitor.• An …
- Induction Heat seat springs for powder coat Class: Other Induction Applications
Intro: Heat seat springs for powder coat Objective Heat the steel spring assemblies of automotive seats to powder coatMaterial Steel wire springs ~24” (61 cm) long, 1/8 “ (3.175mm) diameter cross sectionTemperature 500 F (250 C)Frequency 57 kHzEquipment P…
Recommended
Air Cooled clamp coil (half-open coil) for preheating gas pipeline
U shape air cooled induction coil by UM-100C-HF for pipeline preheating
induction brazing diamond segment
induction melting for crystal growth
induction unassemble 2Ton guard ring of turbine
induction preheating D5000mm end ring for welding by 2 UM-DSP80A-HF at the same time
induction preheating D1219mm pipeline for welding by UM-DSB80AB-MF air cooled induction heater and i
induction preheating and heat treatment for 18Ton control valve of 600MW turbine