- Induction Braze Copper Tube to Brass Fitting Class: HF Induction Brass Solder
Intro: Objective To use induction heating to braze a copper tube to a brass fitting using a preform braze wire. Processing is to occur under an atmosphere of Nitrogen and 4% Hydrogen gas. The braze preforms melt at 1190F, but the parts need to be kept below 1300
- Induction Brazing Eyeglass Frame Assembly Class: HF Induction Brazing
Intro: Objective Produce repeatable braze joints for the assembly of eyeglass frames. Induction heating is to be used to achieve quality braze joints on the nose bridge, brow bridge and nose piece.Brazing is to be done at 1300F with approximately 3-5 seconds all
- Induction Brazing Copper Tube Class: HF Induction Brazing
Intro: Objective To braze a copper tube ( 3/8″ OD by 2-4″ long) into a 3/8″fitting in less than 10 seconds. Heating must take place in achannel type coil to allow for easy loading of parts.Material Copper Tubing and Fitting with Braze and Stay Silv White FluxT…
- Induction Brazing Carbide Tips on Drill Bits Class: HF Induction Brazing
Intro: Objective To braze carbide cutting tips to drill bits ranging in size from 0.5″ to 1.5″ in diameter. The brazing takes place at 1900F and is presently done in 11 seconds for the 0.5″ diameter bit and 39 seconds for the 1.5″ diameter bit. Customer goals…
- Induction Brazing Steel Tube with Copper Ring Class: HF Induction Brazing
Intro: Objective To heat an oil suction assembly (steel tubing and filter cap) to 1,850F (1010C) within 15 seconds for a brazing application.Material 0.125” (3.2mm) diameter steel tube and filter cap assembly, high temperature brazing flux, copper ring.Temperatu
- Induction Brazing Turbine Blades Class: HF Induction Brazing
Intro: Objective To heat an inconel turbine blade in a vacuum to 2000F and hold temperature for five minutes for a nickel brazing application.Material Inconel turbine blades, nickel metering plates, nickel brazeTemperature 2050FFrequency 20 kHzEquipment ABS Mark
- Induction Brazing Steel Fitting Class: HF Induction Brazing
Intro: Objective To heat a steel hydraulic hose fitting in an inert atmosphere to 2200F within 7 seconds for brazing without any carbon buildup.Material Three-opening steel hydraulic fitting, pure copper braze pasteTemperature 2200FFrequency 273 kHzEquipment UM-
- Induction Brazing Steel Conduit Class: HF Induction Brazing
Intro: Objective To heat a stainless steel conduit, ferrule and elbow assembly to 1400F (760C) within 20 seconds for brazing.Material 6”(152.4mm)long x 0.5”(12.7mm) diameter stainless steel conduit, 0.5”(12.7mm) long x 0.5”(12.7mm) diameter ferrule, 2”(50.8m…
- Induction Annealing steel tubes Class: HF Induction Annealing
Intro: Objective To heat steel tubes to 2000 F (1093 C) in an inert atmosphereMaterial 0.1” (2.54mm) diameter stainless steel tubeTemperature 2000 FFrequency 333 kHzEquipment • 10 kW induction heating system, equipped with a remote workhead containing one 1.0μ…
- Induction Annealing Motor Shaft Class: HF Induction Annealing
Intro: Objective Annealing the end of a steel hydraulic motor shaft prior to machiningMaterial .75” (19mm) diameter steel rod, 6” (152.4mm) long with a keyway at the endTemperature 1350 F (732 C)Frequency 359 kHzEquipment • UM-06A-UHF induction heating system,…
Recommended
Air Cooled clamp coil (half-open coil) for preheating gas pipeline
U shape air cooled induction coil by UM-100C-HF for pipeline preheating
induction brazing diamond segment
induction melting for crystal growth
induction unassemble 2Ton guard ring of turbine
induction preheating D5000mm end ring for welding by 2 UM-DSP80A-HF at the same time
induction preheating D1219mm pipeline for welding by UM-DSB80AB-MF air cooled induction heater and i
induction preheating and heat treatment for 18Ton control valve of 600MW turbine