- Induction Brazing Brass Trap Block Class: HF Induction Brass Solder
Intro: Objective Block is heated to 1400F to braze trap tube to assemblyMaterial brass block and pre-formed tubesbraze pre-formsTemperature 1400 F (760C)Frequency 357 kHzEquipment UM-UHF-20kW induction heating system including• Coil: custom-designed 2-turn split
- Induction Brazing Plumbing Class: HF Induction Brazing
Intro: Objective A copper-brass fluids union is brazed under constrained conditions (onboard a submarine), where access is limited and flame is not allowed.Material copper and brass plumbing componentsTemperature 750C (1380 F)Frequency 245 kHzEquipment UM-UHF-20
- Induction Brazing carbide Class: HF Induction Brazing
Intro: Objective Braze a carbide wear pad to steel for automated surgical forcepsMaterial Steel assembly 1/2” (127 mm) long, 1/8 “ (3.175 mm)cross section Carbide wear pad Braze alloyTemperature 1350-1400 F (732- 760 C)Frequency 313 kHzEquipment UM-UHF-4 kW, i…
- Induction Brazing Steel-carbide tool Class: HF Induction Brazing
Intro: Objective Provide a solution to this steel-carbide brazing applicationMaterial • Body 10mm; carbide tip 57 x 35 x 3 mm• Braze shim• Braze flux whiteTemperature 750C (1382F)Frequency 152 kHzEquipment UM-UHF-10kW induction heating system, equipped with a …
- Induction Brazing Steel to Steel Class: HF Induction Brazing
Intro: Objective To braze O-ring Face (ORFS) sleeve or male connector to a steel tube.Material • Steel tube, 1 inch (2.54 cm) OD• O-ring Face Seal sleeve and a male connector fittings• Preform braze rings• White SureFlow flux• Steel support mandrelTemperatur…
- Induction Brazing carbide to steel Class: HF Induction Brazing
Intro: Objective Braze a carbide sleeve to a steel ‘T’ shankMaterial 2.0” (51mm) OD carbide sleeve, 1.0” (25.5mm) high braze joint, 1.5 ” (38 mm) steel ‘T’ , 50% silver braze ringTemperature 1292 F (700 C)Frequency 257 kHzEquipment • UM-UHF-10 kW inductio…
- Induction brazing copper to copper Class: HF Induction Brass Solder
Intro: Objective To braze copper to copper bus bar assemblies togetherMaterial • 2 copper bus bars 6” (152.4mm) wide, 2’ (609.6mm)long, 2 copper bars 6”(152.4mm) wide, 18” (457.2)long & 3/8” (9.65mm) thick• braze shim preforms and white fluxTemperature…
- Induction Brazing stainless steel Class: HF Induction Brazing
Intro: Objective1st Application: Braze hub assembly to needle holder2nd Application: Braze Large tube to ring joint Material 1st Application: Steel hub assembly and needle 0.1” dia (2.5mm)2nd Application: Steel tube 1” OD (25.4 mm) and ringTemperature 1400 F (7…
- Induction Brazing copper tube & pipe Class: HF Induction Brazing
Intro: Objective Braze brass fitting with o-ring to various diameters of copper tube.Material Various copper tubes ranging from 3/8” to 7/8” diameter and 2-3’ long, female brass fittings with o-ring, silver solder rings and glass beaker.Temperature 1300 F (704…
- Induction Brazing carbide teeth to steel pipe Class: HF Induction Brazing
Intro: Objective Brazing carbide teeth to a steel jaw in less than 5 minutesMaterial Steel pipe jaw, 0.5” (12.7mm) dia, 1.25” (31.75mm) long, 0.25” (6.35mm) thick carbide teeth, black flux and silver copper braze shimsTemperature 1292F (700C)Frequency 257kHzEq…
Recommended
Air Cooled clamp coil (half-open coil) for preheating gas pipeline
U shape air cooled induction coil by UM-100C-HF for pipeline preheating
induction brazing diamond segment
induction melting for crystal growth
induction unassemble 2Ton guard ring of turbine
induction preheating D5000mm end ring for welding by 2 UM-DSP80A-HF at the same time
induction preheating D1219mm pipeline for welding by UM-DSB80AB-MF air cooled induction heater and i
induction preheating and heat treatment for 18Ton control valve of 600MW turbine