- Induction Preheating oil drilling shaft Class: Induction Tempering or Preheating
Intro: Preheating oil drilling shaft Objective To preheat a steel pipe to 500F (260C) before welding.Material Steel shaft assembly 5” to 8” OD (127-203.2mm) with a 2” (50.8mm) heat zone.Temperature 500F (260C), if higher temperatures are required, heat ti…
- Induction Tempering Spring Class: Induction Tempering or Preheating
Intro: Tempering Spring Objective Temper a spring by heating it to 300C (570F) in 2 – 4 secondsMaterial Stainless steel AISI 302 springs- different length from 60 to110 mm outer diameters 8 mm.- wire diameter from 0.3 to 0.6 mmTemperature 300C (570F)Freque…
- Induction Pre-heating Truck Axle Class: Induction Tempering or Preheating
Intro: Pre-heating Truck Axle Objective To pre-heat the seam of a truck axle to over 300F within 15 seconds for a welding application and maintain temperature within the welding zone for 15 seconds after the power isturned off.Material Steel truck axle; 350 …
- Induction Preheating Titanium Rods Class: Induction Tempering or Preheating
Intro: Objective To heat titanium rod blanks prior to forging into a turbine blade.Material Titanium rod blanks 0.591″(15.01mm) OD by 11.8″(299.7mm) longTemperature 2030F(1110C)Frequency 64 kHzEquipment • UM-HF-45kW induction heating system equipped with a rem…
- Induction Curing Ceramic Fiber Class: Induction Tempering or Preheating
Intro: Objective To heat-cure a NextelTM Ceramic fiberMaterial Ceramic fiber 30,000 (9,145) ft(m) Steel tubeTemperature indicating paintTemperature 1300(700) F(C)Frequency 70 kHzEquipment UM-HF-45kW, 50-450 kHz solid-state induction power supply with a remote he
- Induction Curing Measuring Tape Paint Class: Induction Tempering or Preheating
Intro: Objective To heat measuring tape stock at a maximum rate of 600 feet per minute to cure the applied paint. The heating coil is to accommodate the 3/8″ wide stock within the customer’s current framework. Curing must occur above 400F at the rate specified.…
- Induction Coating Aluminum Class: Induction Tempering or Preheating
Intro: Objective To heat an aluminum molding shape in order to activate an adhesive coating prior to applying the vinylMaterial Aluminum molding folded from a flat sheet measuring 2″ wide and 0.03″ thick. The final form measures 5/8″ by 1″Temperature 500FFreq…
- induction vacuum coating with multi UM-DSP induction heater Class: Induction Tempering or Preheating
Intro: induction vacuum coating with multi UM-DSP induction heater
Recommended
Air Cooled clamp coil (half-open coil) for preheating gas pipeline
U shape air cooled induction coil by UM-100C-HF for pipeline preheating
induction preheating D5000mm end ring for welding by 2 UM-DSP80A-HF at the same time
induction preheating D1219mm pipeline for welding by UM-DSB80AB-MF air cooled induction heater and i
induction preheating and heat treatment for 18Ton control valve of 600MW turbine
induction preheating and heat treatment after welding for 600MW turbine
induction preheating and heat treatment after welding for 600MW turbine by UM-DSP air cooled machine
induction preheating (250 degree) and heat treatment (710 degree) for 30Ton control valve of 1000MW