Induction Brazing brass faucet Class: HF Induction Brass Solder Intro: Objective Brazing two joints on a brass bathroom faucet assemblyMaterial Brass bathroom fittings 1” OD, brazing rings, fluxTemperature 1148 F (620 C)Frequency 90 kHzEquipment • UM-HF-90kW induction heating system, equipped with a remote workhead containi…
Induction Brazing copper pivot Class: HF Induction Brass Solder Intro: Objective Brazing a copper pivot assemblyMaterial Two copper uprights 2” (5cm) wide x 4” (10.2cm) high, copper base 3” (7.6cm) x 2” (5cm) and .5” (1.3mm) thick with 2 channels for the uprights to the slide into, braze shims and black fluxTemperature 1…
Induction Brazing copper joints Class: HF Induction Brass Solder Intro: Objective Brazing a joint between a copper lug and nickel plated copper pins on a pressurized heater connector.Material 1.5” (38.1mm) dia heater connector in a ceramic insulator with L shaped copper lugs and nickel plated copper pins, silver solder and br
Induction Brazing Copper Contacts Class: HF Induction Brass Solder Intro: Objective Heat silver contacts and brass/copper bus for brazing applicationMaterial Silver contact .75 (19mm) diameter, brass and copper bus 2” x 1” (50.8 x 25.4mm), braze shims, white fluxTemperature 1300 F (704 C)Frequency 320 kHzEquipment • UM-UHF-10…
Induction Brazing Brass Trap Block Class: HF Induction Brass Solder Intro: Objective Block is heated to 1400F to braze trap tube to assemblyMaterial brass block and pre-formed tubesbraze pre-formsTemperature 1400 F (760C)Frequency 357 kHzEquipment UM-UHF-20kW induction heating system including• Coil: custom-designed 2-turn split
Induction brazing copper to copper Class: HF Induction Brass Solder Intro: Objective To braze copper to copper bus bar assemblies togetherMaterial • 2 copper bus bars 6” (152.4mm) wide, 2’ (609.6mm)long, 2 copper bars 6”(152.4mm) wide, 18” (457.2)long & 3/8” (9.65mm) thick• braze shim preforms and white fluxTemperature…
Induction Brazing Brass Fittings Class: HF Induction Brass Solder Intro: Objective To heat brass tubing assemblies to 750C for a brazing application. The tubing diameter varies from 3 to 8 inches (76.2 to 203.2 mm)Material Brass tubingBrass flangeBraze ringsBraze fluxTemperature 1382F (750C)Frequency 100 kHzEquipment UM-HF-45
Induction Brazing Copper Fittings Class: HF Induction Brass Solder Intro: Objective Copper ‘tees’ and ‘ells’ are to be brazed to the aluminum body of a refrigeration valveMaterial customer valvecopper fittingsbrazeTemperature 2550 F (1400C)Frequency 285 kHz Equipment UM-UHF-15KW induction heating system including a workhea…
Induction Brazing Brass Fitting to Copper Air Lines Class: HF Induction Brass Solder Intro: Objective To braze brass end-connectors to copper tubes used in aircraft assembly air linesMaterial brass end connectors, copper tubes of different diametersTemperature 1400 F 750CFrequency 350 kHzEquipment UM-UHF-6KW induction heating system, including a
Induction Braze Copper Tube to Brass Fitting Class: HF Induction Brass Solder Intro: Objective To use induction heating to braze a copper tube to a brass fitting using a preform braze wire. Processing is to occur under an atmosphere of Nitrogen and 4% Hydrogen gas. The braze preforms melt at 1190F, but the parts need to be kept below 1300
